[SIPHEC home]

FX2-56-uMod  EZ-USB FX2LP-56 Micro Module

Category: Development Board, Microcontroller, Cypress CY7C68013A, FX2, FX2LP
Keywords: Microcontroller, Development Board, Prototype Board, Evaluation Kit, HighSpeed USB 2.0, EZ-USB, Cypress CY7C68013A, FX2 Board, USB2ATA

Cypress CY7C68013A - 56 Development Board / Prototype Board with USB2 HighSpeed MiniUSB,
CY7C68013A Board (EZ-USB FX2LP Microcontroller) with Cypress CY7C68013A-56LFXC

• Cypress CY7C68013A-56LFXC - low power Version of CY7C68013-56, full USB2 specified
• micro board, board dimensions 37mm x 25mm (mini module)
• USB2 High Speed (480Mbit/s)
• all pins available on headers (2,54mm-/0,1" pitch)
• Mini USB connector
• 128kbit EEPROM onboard 
• onboard voltage regulator (bottom side)
• GPIF Interface
• solder pads for reset jumper
• power led
  
• device can be configured / programed / booted over USB and by the onboard eeprom for stand alone
  
  
• fully assembled board comes with development kit (CD), Mini USB-Cable, and schematic
   
• optional:
  female connectors 2x (2x12 pins) are available

Features of EZ-USB FX2LP™ USB Microcontroller CY7C68013A (Cypress CY7C68013A-56)
 

• software: 8051 code runs from:
  — internal RAM, which is downloaded via USB
  — internal RAM, which is loaded from EEPROM
  — external memory device (128 pin package)
• 16 KBytes of on-chip Code/Data RAM
• four programmable BULK/INTERRUPT/ISOCHRONOUS endpoints
  — Buffering options: double, triple, and quad
• additional programmable (BULK/INTERRUPT) 64-byte endpoint
• 8- or 16-bit external data interface
• integrated, industry-standard enhanced 8051
  — 48-MHz, 24-MHz, or 12-MHz CPU operation
  — four clocks per instruction cycle
  — two USARTS
  — three counter/timers
  — expanded interrupt system
  — two data pointers
• 3.3V operation with 5V tolerant inputs
• GPIF (General Programmable Interface)
  — allows direct connection to most parallel interface
  — programmable waveform descriptors and configuration registers to define waveforms
  — supports multiple Ready (RDY) inputs and Control (CTL) outputs
• vectored USB interrupts and GPIF/FIFO interrupts
• separate data buffers for the Set-up and Data portions of a CONTROL transfer
• integrated I2C controller, runs at 100 or 400 kHz
• four integrated FIFOs
  — integrated glue logic and FIFOs lower system cost
  — automatic conversion to and from 16-bit buses
  — master or slave operation
  — uses external clock or asynchronous strobes
  — easy interface to ASIC and DSP ICs
  
  EZ-USB FX2LP™ USB Microcontroller CY7C68013A  datasheet (pdf)

EZ-USB FX2LP Development Tools:

• development tools supplied by www.cypress.com

CY3681 EZ-USB FX2 Development Kit

CY3681B EZ-USB FX2 Development Kit

Free available development environment and sources from Cypress:

• cy3684_ez_usb_fx2lp_development_kit_14.zip
• cy3684_ez_usb_fx2lp_development_kit_15.zip
• cy3684_ez_usb_fx2lp_development_kit_17.zip
• windows_mass_storage_driver_v_6_01_13.zip
• and more

Compiler:

• Free Keil C-Compiler

Tools:

• USBView

Applications:

• USB to IDE (USB2IDE, USB2ATA)
• USB to Compact Flash Card (USB2CFCard)

[SIPHEC home]